Real time measurement helps dairies cut product loss as 2025 sustainability targets loom

/INSCollo dielectric sensors identify the unique fingerprint of each liquid as it moves through the pipeline, enabling operators to optimize their dairy plant and reduce product waste

- Product loss in dairy processing is becoming a pressing concern as companies in the EU are required to report for the EU CSR Directive for the first time in 2025

- Product loss in push-out processes can be prevented by more accurate detection of the contents in the pipeline. This can be achieved using dielectric detection

- More stringent regulatory requirements and changing consumer preferences are powerful incentives for dairy companies to reduce product loss

As dairies scramble to meet sustainability targets ahead of the first year of reporting for the EU CSR Directive, the significant losses in push-out processes have been identified as low hanging fruit by many companies.

From 2025, listed companies in the EU with more than 500 employees will be required to report sustainability information according to the new mandatory European Sustainability Reporting Standards (ESRS). This requirement will be expanded over the coming years to cover further categories of companies.

Product loss is a significant problem at many dairies and can have a large impact on the carbon footprint. Hundreds of liters of product is often lost to the drains when liquid product is displaced with water by pushing it from one processing step to another. Frequently, as much as 1% of dairy production can be wasted in the push-out between product batches. For an average dairy plant processing 250,000 tons of raw milk annually, this means a loss of 2,500 tons of raw milk, as well as unnecessary CO2 emissions upstream in the supply chain.

However, inaccurate measuring technologies frequently prevent operators from addressing this issue in an effective way, as it can be difficult to correctly identify the product that moves through the pipeline. But with appropriate measuring technology, the end of one batch and the beginning of the next can be accurately located. If it is not, the small losses at each push-out point, of which there can be hundreds, accumulate and become significant by the end of the process.

Pipeline contents are commonly measured by one of the three technologies – flow meter, turbidity sensor or conductivity sensor. Flow meters estimate the arrival of the product at the push-out point based on the system flow rate; turbidity sensors monitor the interaction between a light beam and the liquid; and conductivity sensors operate by measuring the electrical conductivity of the liquid.

A fourth method is based on monitoring the dielectricity of the liquid, i.e. its ability to hold electric charge. This is achieved by using a sensor that accurately identifies the substance moving through the pipeline as a radiofrequency electromagnetic field is induced into the liquid. Different liquids have different dielectricity, making them distinguishable from each other, giving each liquid a unique fingerprint.

Measuring the dielectric properties of the liquid provides significant advantages over traditional approaches. Flow meters have very low accuracy and turbidity sensors cannot distinguish transparent liquids, such as whey concentrate, from water, and become clogged by thick liquids, like cream. The electrical conductivity of milk-based products is close to that of water, which translates into low sensitivity for conductivity sensors when detecting product interfaces,” says Matti Järveläinen, CEO of Collo, a leading manufacturer of dielectric liquid analyzing systems. 

 

One of the key benefits in Collos dielectric sensors is that the technology works with any liquid. Unlike turbidity sensors, it can accurately detect transparent, opaque and thick liquids, like whey concentrate or cream, from water, in addition to other milk-based and non-milk liquids.

 

The dielectric sensor can detect any liquid, whether it is thin, thick, colored, colorless, opaque or transparent. This means that the same measuring technology can be applied across the dairy plant, while in the past the plant needed to select the sensor based on the type of liquids processed in each particular location,” adds Järveläinen.

A solution that can be scaled easily across the plant has been our goal from the start. We use sophisticated machine learning techniques to quickly calibrate our system to new liquids. The result is actionable information, like percentage of water in the product, which is transferred to the plant automation system, enabling process optimization,” Järveläinen continues.

Collo sensors were recently installed in four locations in the raw milk reception of a dairy plant processing 243 million liters of raw milk per year. The plant previously used flow meters for controlling the push-outs. However, due to their low accuracy, what appeared to be optimal timing actually resulted in losses amounting to 600,000 liters per year. With the far higher accuracy of the dielectric sensor, 108 times better than the flow meter, losses were reduced to just 5,000 liters per year – a reduction by more than 99%.

The dairy has now decided to introduce Collo’s solution throughout the plant and to automate the process.

 

In this case example, the conductivity sensor was previously used in cream push-out, however it was inaccurate and reacted slowly to the cream/water interface, leading to losses of 500 liters of product in each push-out. With Collo, the optimal timing prevents losses. Cream is one of the costliest dairy products to produce and is also very costly to dispose of as waste.

 

Large dairy and other food producers are currently increasing their efforts to reduce their environmental impact ahead of environmental targets that loom in the near future, mainly in 2025 and 2030. Most of the greenhouse gas emissions caused by dairy operations originate at the farm. For instance, Nestlé, in its sustainability report[1], outlines how just 5% of its greenhouse gas emissions comes from its own operations, whereas 95% is made up of emissions in the supply chain. Raw milk production is the largest single source of emissions in dairy production, which any waste of milk-based raw material needs to be prevented and, preferably, eliminated.

Other companies have similar targets. Danone is committed to reducing its own greenhouse gas emissions by 47.2% by 2030 and those in the supply chain by 42%. Fonterra aims to reduce manufacturing emissions by 50% by 2030.

The year 2025 is an important milestone for many companies, as the 2030 Agenda for Sustainable Development was adopted by all United Nations members in 2015 and many companies set themselves 10-year targets at the time. The European Union is committed to implementing the UN Sustainable Development Goals and the CSR Directive is one way the business community is made to play its part.

In addition to the regulatory requirements, changing consumer preferences is another powerful incentive for dairy producers to implement more eco-friendly production methods. A study by McKinsey and NielsenIQ[2] found that products making claims related to sustainability have faster market growth – over a 5-year time span, such products grew about 18 percent more than the expectation was at the beginning of the period.

– Waste in dairy processes needs to be reduced. Environmentally compatible processes are demanded by regulators and consumers alike. Wasting hundreds of liters of valuable product in every batch makes no sense when this can be prevented with the right technology. But it does not end there. With Collo’s versatile technology we can help plants reduce water use too, an area which is also of keen interest for our customers and regulators alike. Working together with its customers, Collo can play a significant role in achieving a more sustainable dairy process, concludes Järveläinen.

 

Press Contacts:

Mikko Tielinen, Head of Sales ColloidTek
Phone: +358 40 728 4135
E-mail: mikko.tielinen@collo.fi
www.collo.fi


Collo

Collo is an industrial liquid process performance solution developed by ColloidTek Oy (Collo). The company was founded in 2017 after extensive scientific research in electromagnetic field (EMF) measurement technology at Tampere University. Collo’s cloud-based process performance solution helps industrial customers understand and enhance their liquid processes. Among the customers are well-known industrial companies like Danone, Fonterra, Valio, Ecolab and ABB.



[1] Creating Shared Value and Sustainability Report 2023; Nestlé

[2] Consumers care about sustainability—and back it up with their wallets; McKinsey and NielsenIQ ; February 2023

Rating:

vote data

Let us know if you are going to use this press release. Thank you!

 

Company Information

Collo Logo

Other inquiries: info@collo.fi
Email format: firstname.lastname@collo.fi

www.collo.fi

Press contact

Tuuli Potila
Marketing Manager

Tel: +358 10 200 1770

tuuli.potila@collo.fi

     Via social media

Social media coming soon

Company Information

Collo Logo


Other inquiries: info@collo.fi
Email format: firstname.lastname@collo.fi

www.collo.fi

Press contact

Tuuli Potila
Marketing Manager

Tel: +358 10 200 1770

tuuli.potila@collo.fi

     Via social media

Social media coming soon

About ColloidTek Oy

 

Collo is an industrial liquid process performance solution, developed by ColloidTek Oy (Collo), founded in 2017 after extensive scientific research in measurement technology at Tampere University by its founders and key personnel. Collo develops and commercializes the Collo technology for various industries, helping customers better understand and develop their liquid processes. Amongst the customers are well-known industrial companies like ABB, Danone, Evonik, LKAB, Element Six, Kemira and Outotec.

Publications